Content Comparison

Panel

borderColor	#000000
bgColor	#f0f0f0
titleColor	#FFFFFF
titleBGColor	#4C5356
title	Project

Projecttitel: Swenigiser

Status:
Status
colour Green
title finished

Startdate: 03/2023

Duedate: 04/2023

updated 23.05.2023

Manufacture link: https://analogsweden.com

Image RemovedImage Added

Info:

title

Info

The Swenigiser is available in prebuilt and DIY Versions.

It's a fully expanded Orgon Enigiser clone - "more or less a replica", since the Voice PCB and Panel Pcbs are reverse engineered.

MIDI Input is on the rear, powerswitch too.

...

I got a PCB set, case and few parts (DIY Kit) and built the device in around 5-7hours. It was fast, because I built 2 years ago the RENIGISER clone too and have a lot of experience and the correct tools.

The Build is medium - not complicated and you don´t need special tools, a scope isn't requiredcan be very useful to check the waveforms while calibration.

The most infos are described here: https://analogsweden.com/support

BOM (copy here) : SWEnigiser BOM public.xlsx: https://docs.google.com/spreadsheets/d/1Y-wN3K0ySpOIgIz0oumLv88jeU2fVrmLDgAGZNXTImY/edit?usp=sharing

BOM notes: please read my Build tips - maybe you need some additional stuff.. (extra nuts, washers, gaffe tape, conductive tape) which isn't described in the official BOM

Buildguide (copy here): : https://docs.google.com/document/d/1TawPs6FYYtUiqXIjr_ct7wg1Ha2BtqRQh8R6SiJCEC0/edit?usp=sharing

(builguide backup: here)

Calibration guide: https://docs.google.com/document/d/e/2PACX-1vT6ixpvVsDYjM1PqPgLdzOc65GO3PApa-8_ZfttzhNT1LkMXzbI6MDWRsOo-P5VEh3SpZX4UKWi19R7/pub14O1EXb5Ze5UpgVeaVhvRWePab4jU7Cl1Uu0GKmQ2Cdg/edit?usp=sharing

Potentiometer Guide:

Image Removed

...

Usermanual (copy here): https://analogsweden.com/wp-content/uploads/2023/04/swENIG-quickstart.pdf

(backup here)

DIY BUILD GUIDE ADDON /Support from me:

the biggest risk and challenge in this build:

Risks/Problems/Issues

Issue ID	Date	Typ	Issue	Solution	affected version	Fixed version
1	22.04.2023	info/fix	the panel pcb is very close to the aluminum case - its easy to run in malfunctions and defects !!

Since

Since I built the RENIGISER, I know excactly how to fix it with a workaround.

use gaffa tape and put this on the case from inside , 2 layers are fine

use additional washers on the potentiometers

and rotary switches to

(or nuts)

use at the rotary switches the nut or you can risk that the lock washer get loose, and you get more clearance/distance between the case and panel pcb

DO NOT solder all cables

NOT

thru the holes, just on top of the pads is fine. (as shown in my pictures)

solder the potentiometers : add some solder on all pads !! then install the pots, use additional washers or nuts and then use nuts to fix they from outside - then solder the potentiometers.

in this way you have enough space between the case and pcb with less risks.

release April 2023

-

2

22.04.2023

info/fix

the Upper pcb for the jacks: a lot of traces are under the jacks and at the tall trimmer, and if you press the jacks to close on the pcb, you can damage the PCB coating - get shorts

and bleeds

and bleeds (same was on the TTSH project and many other projects)

Image Removed

Image Added

use tape as shown in

my picture

my picture and do make sure there's no mechanical stress on the jacks while soldering.

Image Removed

Image Added	release April 2023	-
3	22.04.2023	build info	do not forget to install the Jumpers/bridges as described in the guide or you can't hear something
4	22.04.2023	BOM info	1pf cap	use 3.3pf or do not install a cap.. works without too
5	22.04.2023	build info	diodes D9/D10 install this.. ( some clones and some originals dont have this.)

PCB Pictures:

Image RemovedImage RemovedImage RemovedImage RemovedImage RemovedImage RemovedImage Removed

PCB Pictures assembled

Image RemovedImage RemovedImage RemovedImage Removed

...


6	22.04.2023	info	in case you have hum - check the MIDI wiring
7	22.04.2023	info	please report bugs and infos here.. there's a comment function on this website